![]() ![]() ![]() These give you more control over the placement of the text around the curve. Selecting both the circle and the text allows you to use the Fit Text to Path menu tools. Use the Text Tool to select just the text, and change the font, size, kern or any other editing that you would normally do to the text. Once you have your text in place, you can use all of the standard tools available for editing text, as well as manipulating the fitted text. When you click on the mouse with this cursor showing, the text will conform to the inside of the circle. Clicking the mouse with this cursor showing will place typed text onto the page of the circle.Ĭursor 3 appears when the cursor is moved just to the inside of the circle and is the Paragraph Text Tool. Each shape is pictured and described below.Ĭursor 1 is the standard text cursor and will produce text anywhere on the page.Ĭursor 2 appears when the cursor is right on top of the circle. Depending on how close you place the cursor to the circle, you will see the cursor change shape. Next, select the Text Tool on the toolbar and line up the cursor with the circle. Use the Ellipse Tool (circled in green on the toolbar) and draw any size circle for our example. Well, it’s possible in a few easy steps in CorelDRAW! Follow the directions below to see how you can master this technique. When the laser receives a job where the line weights are too large, the laser system will just beep when you attempt to run the job.Have you ever had that engraving job that would have looked even better if you could have just curved the text around the photograph, or been able to have the text along a line you drew? 001 inch, vector cutting will not be possible. 010 and a line weight this large disables vector cutting. In the AutoCAD print window, set the pen colors that you are using to. ![]() Setting both your AutoCAD page and the Dashboard print driver Piece Size to a square configuration (24” x 24”, for instance) is necessary to overcome AutoCAD’s tendency to rotate your artwork 90 degrees. Make sure to set the Piece Size in the Dashboard so is matches your AutoCAD page size. Set the Piece Size to match your AutoCAD page size. If you have a 24 x 24 inch page and you are printing to a bed size of 24 x 12 inches (610 x 305 mm), the objects in the lower 12 inches will not be processed.Ģ. Place all of your objects in the upper portion of the AutoCAD page (see illustration below). The page in the example below is set to 24 x 24 inches.ġ. A square page in AutoCAD prevents the objects from rotating 90 degrees when you print them. When printing from AutoCAD you will need to set up your AutoCAD page so that it is square. Color mapping assigns different Speed and Power settings to an object based on its color allowing you to both cut and mark in a single setup.įor a detailed description of how Color Mapping works, refer to this tech library article: Setting Color Mapping Presets in the Driver. While your laser system is capable of handling complex drawings, users may find that eliminating extraneous detail before “Printing/Plotting” may make their laser equipment more productive.Ĭreating objects of different colors in AutoCAD allows the user to take advantage of the Vector Color Mapping capabilities of the Epilog Dashboard print driver. Since there is no limit to the level of complexity that an AutoCAD drawing can achieve, users should keep in mind that the laser is a 2D cutting machine that usually cuts a single piece of material in any given job. Previewing your image before sending it to the laser is very helpful in preventing print problems.ĪutoCAD is capable of producing extremely complicated drawings with many layers, colors, etc. Since there are so many different settings that AutoCAD requires, it is important that you double-check all of the settings that are critical to success. Sending jobs from AutoCAD is heavily dependent on the print settings in the AutoCAD Print/Plot window. AutoCAD versions 14 to the present are typically compatible with Epilog systems, though each version uses slightly different printing conventions that may or may not affect the way you print, and different versions may produce different output from the laser. Like any tool, understanding how it works and its limitations are helpful in getting the most out of it. The following article includes general instructions and tips on printing to an Epilog Laser system from AutoCAD Software.ĪutoCAD is a very powerful software tool that is often used in conjunction with the laser for cutting applications. How do I print to the laser from AutoCAD? ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |